Datasheet Texas Instruments TPS61092RSARG4 — 数据表
| 制造商 | Texas Instruments |
| 系列 | TPS61092 |
| 零件号 | TPS61092RSARG4 |
5V输出，500mA，96％高效升压转换器，20uA，QFN-16 16-QFN -40至85
数据表
TPS6109x Synchronous Boost Converter With 2-A Switch datasheet
PDF, 1.0 Mb, 修订版: C, 档案已发布: Dec 24, 2014
从文件中提取
价格
状态
| Lifecycle Status | Active (Recommended for new designs) |
| Manufacture's Sample Availability | Yes |
打包
| Pin | 16 | 16 |
| Package Type | RSA | RSA |
| Industry STD Term | VQFN | VQFN |
| JEDEC Code | S-PQFP-N | S-PQFP-N |
| Package QTY | 3000 | 3000 |
| Carrier | LARGE T&R | LARGE T&R |
| Device Marking | 1092 | TPS6 |
| Width (mm) | 4 | 4 |
| Length (mm) | 4 | 4 |
| Thickness (mm) | .9 | .9 |
| Pitch (mm) | .65 | .65 |
| Max Height (mm) | 1 | 1 |
| Mechanical Data | 下载 | 下载 |
参数化
| Duty Cycle(Max) | 100 % |
| Iq(Typ) | 0.02 mA |
| Operating Temperature Range | -40 to 85 C |
| Package Group | QFN |
| Rating | Catalog |
| Regulated Outputs | 1 |
| Special Features | Enable,Frequency Synchronization,Light Load Efficiency,Load Disconnect,Power Good |
| Switch Current Limit(Min) | 2 A |
| Switch Current Limit(Typ) | 2 A |
| Switching Frequency(Max) | 700 kHz |
| Switching Frequency(Min) | 500 kHz |
| Type | Converter |
| Vin(Max) | 5.5 V |
| Vin(Min) | 1.8 V |
| Vout(Max) | 5 V |
| Vout(Min) | 5 V |
生态计划
| RoHS | Compliant |
设计套件和评估模块
- Evaluation Modules & Boards: TPS61090EVM-029
TPS61090 Evaluation Module
Lifecycle Status: Active (Recommended for new designs)
应用须知
- Five Steps to a Good PCB Layout of the Boost ConverterPDF, 701 Kb, 档案已发布: May 3, 2016
- Minimizing Ringing at the Switch Node of a Boost ConverterPDF, 201 Kb, 档案已发布: Sep 15, 2006
The application report explains how to use proper board layout and/or a snubber to reduce high-frequency ringing at the switch node of a boost converter. - Basic Calculation of a Boost Converter's Power Stage (Rev. C)PDF, 186 Kb, 修订版: C, 档案已发布: Jan 8, 2014
This application note gives the equations to calculate the power stage of a boost converter built with an IC with integrated switch and operating in continuous conduction mode. It is not intended to give details on the functionality of a boost converter (see Reference 1) or how to compensate a converter. See the references at the end of this document if more detail is needed. - Optimizing Transient Response of Internally Compensated DC-DC Converters (Rev. A)PDF, 1.1 Mb, 修订版: A, 档案已发布: May 11, 2015
- Extending the Soft Start Time Without a Soft Start Pin (Rev. B)PDF, 387 Kb, 修订版: B, 档案已发布: Jun 15, 2017
- Choosing an Appropriate Pull-up/Pull-down Resistor for Open Drain OutputsPDF, 130 Kb, 档案已发布: Sep 19, 2011
- QFN and SON PCB Attachment (Rev. B)PDF, 821 Kb, 修订版: B, 档案已发布: Aug 24, 2018
- IQ: What it is what it isn’t and how to use itPDF, 198 Kb, 档案已发布: Jun 17, 2011
- Performing Accurate PFM Mode Efficiency Measurements (Rev. A)PDF, 418 Kb, 修订版: A, 档案已发布: Dec 11, 2018
When performing measurements on DC-DC converters using pulse frequency modulation(PFM)or any power save mode proper care must be taken to ensure that the measurements are accurate. An accurate PFM mode efficiency measurement is critical for systems which require high efficiency at low loads such as in smart home systems tablets wearables and metering.
模型线
系列: TPS61092 (2)
- TPS61092RSAR TPS61092RSARG4
制造商分类
- Semiconductors > Power Management > Non-isolated DC/DC Switching Regulator > Step-Up (Boost) > Boost Converter (Integrated Switch)