Datasheet Texas Instruments THS3121IDGNG4 — 数据表

制造商Texas Instruments
系列THS3121
零件号THS3121IDGNG4
Datasheet Texas Instruments THS3121IDGNG4

单个低噪声,高输出驱动,475mA电流反馈放大器8-MSOP-PowerPAD -40至85

数据表

Low-Noise, High-Output Drive, Current Feedback Operational Amplifiers datasheet
PDF, 1.3 Mb, 修订版: E, 档案已发布: Oct 12, 2009
从文件中提取

价格

状态

Lifecycle StatusActive (Recommended for new designs)
Manufacture's Sample AvailabilityNo

打包

Pin8
Package TypeDGN
Industry STD TermHVSSOP
JEDEC CodeS-PDSO-G
Package QTY80
CarrierTUBE
Device MarkingAPO
Width (mm)3
Length (mm)3
Thickness (mm)1.02
Pitch (mm).65
Max Height (mm)1.1
Mechanical Data下载

参数化

2nd Harmonic51 dBc
3rd Harmonic50 dBc
@ MHz10
Acl, min spec gain1 V/V
Additional FeaturesN/A
ArchitectureBipolar,Current FB
BW @ Acl130 MHz
CMRR(Min)63 dB
CMRR(Typ)70 dB
GBW(Typ)130 MHz
Input Bias Current(Max)4000000 pA
Iq per channel(Max)4.25 mA
Iq per channel(Typ)3.5 mA
Number of Channels1
Offset Drift(Typ)10 uV/C
Operating Temperature Range-40 to 85 C
Output Current(Typ)475 mA
Package GroupMSOP-PowerPAD
Package Size: mm2:W x L8MSOP-PowerPAD: 15 mm2: 4.9 x 3(MSOP-PowerPAD) PKG
Rail-to-RailNo
RatingCatalog
Slew Rate(Typ)1500 V/us
Total Supply Voltage(Max)30 +5V=5, +/-5V=10
Total Supply Voltage(Min)10 +5V=5, +/-5V=10
Vn at 1kHz(Typ)2.5 nV/rtHz
Vn at Flatband(Typ)2.5 nV/rtHz
Vos (Offset Voltage @ 25C)(Max)10 mV

生态计划

RoHSCompliant

设计套件和评估模块

  • Evaluation Modules & Boards: THS3111EVM
    THS3111 Evaluation Module
    Lifecycle Status: Active (Recommended for new designs)
  • Evaluation Modules & Boards: THS3120EVM
    THS3120 Evaluation Module
    Lifecycle Status: Active (Recommended for new designs)
  • Evaluation Modules & Boards: THS3110EVM
    THS3110 Evaluation Module
    Lifecycle Status: Active (Recommended for new designs)

应用须知

  • Active filters using current-feedback amplifiers
    PDF, 227 Kb, 档案已发布: Feb 25, 2005
  • Expanding the usability of current-feedback amplifiers
    PDF, 215 Kb, 档案已发布: Feb 28, 2005
  • Wideband Complementary Current Output DAC Single-Ended Interface
    PDF, 597 Kb, 档案已发布: Jun 21, 2005
    High-speed digital-to-analog converters (DACs) most often use a transformer-coupled output stage. In applications where this configuration is not practical, a single op ampdifferential to single-ended stage has often been used. This application note steps through the exact design equations required to achieve gain matching from each output as well as a matched input impedance to each of the DA
  • Noise Analysis for High Speed Op Amps (Rev. A)
    PDF, 256 Kb, 修订版: A, 档案已发布: Jan 17, 2005
    As system bandwidths have increased an accurate estimate of the noise contribution for each element in the signal channel has become increasingly important. Many designers are not however particularly comfortable with the calculations required to predict the total noise for an op amp or in the conversions between the different descriptions of noise. Considerable inconsistency between manufactu

模型线

制造商分类

  • Semiconductors > Amplifiers > Operational Amplifiers (Op Amps) > High-Speed Op Amps (>=50MHz)