Datasheet Texas Instruments BQ27200 — 数据表

数据表

价格

状态

打包

生态计划

应用须知

• 下载
  Configuring the bq27000/200 for Gas Gauge Applications
  PDF, 137 Kb, 档案已发布: Aug 29, 2005
  Users of the bq27000 and bq27200 ICs can program ten EEPROM locations to optimize setups for particular battery and host requirements. This application report describes how to configure these ICs for those requirements.
• 下载
  Using the bq27x00 With a Primary Cell Battery
  PDF, 42 Kb, 档案已发布: Dec 15, 2005
  The bq27x00 is an accurate coulomb counter and contains algorithms to dynamically compensate the available capacity for temperature and discharge rate. If direct drive from the gauge to an LED display is not required, the bq27x00 can be used as an accurate gas gauge solution for a primary cell battery. Although the bq27x00 was designed for a single-cell rechargeable lithium-ion or lithium-polymer
• 下载
  Multicell Li-Ion and Li-Pol Battery Gas-Gauge Application Using the bqJunior
  PDF, 58 Kb, 档案已发布: May 26, 2006
  The bqJuniorв„ў series of gas gauges are designed to operate from a single-cell, lithium-ion or lithium-polymer battery. Many applications that could benefit from using these gas gauges use two or more lithium cells in series, where the battery voltage exceeds the operating voltage for the bqJuniorв„ў gas gauges. This application report describes a low-component count solution for using th
• 下载
  Building a Superior Battery Monitor with the bq27x00
  PDF, 43 Kb, 档案已发布: Jun 20, 2005
  The bq27x00 is a complete gas gauge solution for lithium-ion and lithium-polymer batteries. The bq27x00 also has internal registers and control commands that enable the host to use it as a battery monitor. A battery gas gauge solution can be built one of two ways: ignore all algorithms built into the bq27x00 and use the primitive functions to build a fully customized solution, or use some of the h
• 下载
  Choosing Between Battery Gas Gauges & Monitors to Track Charge Availabilility
  PDF, 184 Kb, 档案已发布: Sep 27, 2005
  Some customers are unfamiliar with battery monitors or gas gauges for their handheld portable applications. The intent of this application report is to provide information about TI product families that are excellent options when selecting a battery gas gauge solution.
• 下载
  Complete battery-pack design for one- or two-cell portable applications
  PDF, 164 Kb, 档案已发布: Jul 17, 2006
• 下载
  ESD and RF Mitigation in Handheld Battery Pack Electronics
  PDF, 68 Kb, 档案已发布: Mar 6, 2008
  It is imperative to protect the electronics in a consumer-removable battery pack from ESD damage. Even an upset without permanent damage may be unacceptable to the end-user. Handheld equipment that contains a transmitter also may require protection to guard against improper measurement and/or upset due to the affect of the radio frequency (RF) on the circuitry. Because the RF field strength varies
• 下载
  Feature Set Comparison of bq27x00, bq27x10, bq27500, and bq27510 (Rev. A)
  PDF, 65 Kb, 修订版: A, 档案已发布: Dec 2, 2008
  Feature Set Comparison of bq27x00, bq27x10, bq27500 and bq27510
• 下载
  Single Cell Gas Gauge Circuit Design
  PDF, 154 Kb, 档案已发布: Feb 22, 2008
• 下载
  Single Cell Impedance Track Printed-Circuit Board Layout
  PDF, 403 Kb, 档案已发布: Feb 22, 2008
  bq20z70/90 Printed-Circuit Board Layout Guide
• 下载
  MSP430 Microcontroller SW for Handheld Fuel Gauges and Battery Authentication (Rev. A)
  PDF, 350 Kb, 修订版: A, 档案已发布: May 26, 2010
  MSP430, bq26100, bq26100EVM, bq26150, bq26150EVM, bq26500, bq27000, bq27000EVM, bq27200, b MSP430 Microcontroller Software for Handheld Fuel Gauge & Battery Authentication

模型线

制造商分类

• Semiconductors> Power Management> Battery Management Products> Battery Fuel Gauge