Datasheet Texas Instruments LM3488 — 数据表

制造商Texas Instruments
系列LM3488
Datasheet Texas Instruments LM3488

用于开关稳压器的40V宽Vin低侧N通道控制器

数据表

LM3488/-Q1 Automotive High-Efficiency Controller for Boost, SEPIC and Fly-Back DC-DC Converters datasheet
PDF, 1.7 Mb, 修订版: O, 档案已发布: Jul 6, 2015
从文件中提取

价格

状态

LM3488MMLM3488MM/NOPBLM3488MMXLM3488MMX/NOPB
Lifecycle StatusActive (Recommended for new designs)Active (Recommended for new designs)NRND (Not recommended for new designs)Active (Recommended for new designs)
Manufacture's Sample AvailabilityYesNoYesNo

打包

LM3488MMLM3488MM/NOPBLM3488MMXLM3488MMX/NOPB
N1234
Pin8888
Package TypeDGKDGKDGKDGK
Industry STD TermVSSOPVSSOPVSSOPVSSOP
JEDEC CodeR-PDSO-GR-PDSO-GR-PDSO-GR-PDSO-G
Package QTY100010003500
CarrierSMALL T&RSMALL T&RLARGE T&R
Device MarkingS21BS21BS21BS21B
Width (mm)3333
Length (mm)3333
Thickness (mm).97.97.97.97
Pitch (mm).65.65.65.65
Max Height (mm)1.071.071.071.07
Mechanical Data下载下载下载下载

参数化

Parameters / ModelsLM3488MM
LM3488MM
LM3488MM/NOPB
LM3488MM/NOPB
LM3488MMX
LM3488MMX
LM3488MMX/NOPB
LM3488MMX/NOPB
Approx. Price (US$)0.80 | 1ku
Duty Cycle(Max), %100100100
Duty Cycle(Max)(%)100
Iout(Max), A101010
Iout(Max)(A)10
Iq(Typ), mA2.72.72.7
Iq(Typ)(mA)2.7
Operating Temperature Range, C-40 to 125-40 to 125-40 to 125
Operating Temperature Range(C)-40 to 125
Package GroupVSSOPVSSOPVSSOPVSSOP
RatingCatalogCatalogCatalogCatalog
Regulated Outputs111
Regulated Outputs(#)1
Special FeaturesAdjustable Current Limit,Enable,Frequency Synchronization,Light Load Efficiency,Pre-Bias Start-UpAdjustable Current Limit,Enable,Frequency Synchronization,Light Load Efficiency,Pre-Bias Start-UpAdjustable Current Limit
Enable
Frequency Synchronization
Light Load Efficiency
Pre-Bias Start-Up
Adjustable Current Limit,Enable,Frequency Synchronization,Light Load Efficiency,Pre-Bias Start-Up
Switch Current Limit(Typ), A101010
Switch Current Limit(Typ)(A)10
Switching Frequency(Max), kHz100010001000
Switching Frequency(Max)(kHz)1000
Switching Frequency(Min), kHz100100100
Switching Frequency(Min)(kHz)100
TypeControllerControllerControllerController
Vin(Max), V404040
Vin(Max)(V)40
Vin(Min), V2.972.972.97
Vin(Min)(V)2.97
Vout(Max), V500500500
Vout(Max)(V)500
Vout(Min), V1.261.261.26
Vout(Min)(V)1.26

生态计划

LM3488MMLM3488MM/NOPBLM3488MMXLM3488MMX/NOPB
RoHSSee ti.comCompliantNot CompliantCompliant
Pb FreeNo

应用须知

  • Softstart Using Constant Current Constant Voltage Approach
    PDF, 337 Kb, 档案已发布: Jul 24, 2015
    In many systems backup power is provided either by batteries or simply by a large value capacitor. Inthese applications the capacitor would only provide the current when the primary power source fails.Further, these applications are usually for light load currents. During normal operation the backupcapacitors are kept charged up by a DC/DC converter. The challenge involved in an application
  • Demystifying Type II and Type III Compensators Using Op-Amp and OTA for DC/DC Co
    PDF, 782 Kb, 档案已发布: Jul 11, 2014
  • AN-1286 Compensation For The LM3478 Boost Controller (Rev. C)
    PDF, 356 Kb, 修订版: C, 档案已发布: Apr 23, 2013
    The LM3478 is a low side N-Channel controller for switching regulators. Like many switching controllers,the added flexibility in component selection can cause problems for users when determining thecompensation scheme. It is the goal of this application report to present a decent groundwork to allow thereader to select with confidence the correct compensation components. To achieve this we l
  • AN-1484 Designing A SEPIC Converter (Rev. E)
    PDF, 220 Kb, 修订版: E, 档案已发布: Apr 23, 2013
    In a single ended primary inductance converter (SEPIC) design, the output voltage can be higher or lowerthan the input voltage. The SEPIC converter shown in Figure 1 uses two inductors: L1 and L2. The twoinductors can be wound on the same core since the same voltages are applied to them throughout theswitching cycle.
  • Modeling & Design of Current Mode Control Boost Converters (Rev. B)
    PDF, 316 Kb, 修订版: B, 档案已发布: Apr 23, 2013
    This application note presents a detail modeling and design of current mode control boost convertersoperating in the continuous conduction mode (CCM). Based on the derived small signal models, thedesign of a lag compensator for current mode control boost converters will be detailed. The LM3478 boostcontroller will be used in the example. Simulation and hardware measurement of frequency respo
  • AN-1990 Compensation for Current Mode Control SEPIC Converters (Rev. A)
    PDF, 247 Kb, 修订版: A, 档案已发布: Apr 23, 2013
    This application note discusses the use of SEPIC converters in various applications.
  • LM34xx How to Design Flyback Converter with LM3481 Boost Controller
    PDF, 1.7 Mb, 档案已发布: Sep 21, 2016
    The TexasInstrumentsLM3481boostcontrolleris a versatilelow-sideN-FEThigh-performancecontrollerfor switchingregulators.Thedevicehaswiderangeof applicationssuchas automotivestart-stopapplication,one-cellor two-cellLi-ionbattery-poweredportableBluetoothaudiosystem,industrialsystemisolatedsupplies,and so forth,and supportstopologi

模型线

制造商分类

  • Semiconductors> Power Management> Non-isolated DC/DC Switching Regulator> Step-Up (Boost)> Boost Controller (External Switch)