Datasheet Texas Instruments MSP430F5513 — 数据表
| 制造商 | Texas Instruments |
| 系列 | MSP430F5513 |
MSP430F551x，MSP430F552x混合信号微控制器
数据表
MSP430F552x, MSP430F551x Mixed-Signal Microcontrollers datasheet
PDF, 2.4 Mb, 修订版: M, 档案已发布: Nov 2, 2015
从文件中提取
价格
状态
| MSP430F5513IRGCR | MSP430F5513IZQE | MSP430F5513IZQER | |
|---|---|---|---|
| Lifecycle Status | Active (Recommended for new designs) | Active (Recommended for new designs) | Active (Recommended for new designs) |
| Manufacture's Sample Availability | Yes | No | Yes |
打包
| MSP430F5513IRGCR | MSP430F5513IZQE | MSP430F5513IZQER | |
|---|---|---|---|
| N | 1 | 2 | 3 |
| Pin | 64 | 80 | 80 |
| Package Type | RGC | ZQE | ZQE |
| Industry STD Term | VQFN | BGA MICROSTAR JUNIOR | BGA MICROSTAR JUNIOR |
| JEDEC Code | S-PQFP-N | S-PBGA-N | S-PBGA-N |
| Package QTY | 2000 | 360 | 2500 |
| Carrier | LARGE T&R | JEDEC TRAY (5+1) | LARGE T&R |
| Device Marking | M430F5513 | M430F5513 | M430F5513 |
| Width (mm) | 9 | 5 | 5 |
| Length (mm) | 9 | 5 | 5 |
| Thickness (mm) | .88 | .74 | .74 |
| Pitch (mm) | .5 | .5 | .5 |
| Max Height (mm) | 1 | 1 | 1 |
| Mechanical Data | 下载 | 下载 | 下载 |
参数化
| Parameters / Models | MSP430F5513IRGCR | MSP430F5513IZQE | MSP430F5513IZQER |
|---|---|---|---|
| ADC | Slope | Slope | Slope |
| AES | N/A | N/A | N/A |
| Active Power, uA/MHz | 404 | 404 | 404 |
| Additional Features | USB,Real-Time Clock,Watchdog,Brown Out Reset,IrDA | USB,Real-Time Clock,Watchdog,Brown Out Reset,IrDA | USB,Real-Time Clock,Watchdog,Brown Out Reset,IrDA |
| BSL | USB | USB | USB |
| CPU | MSP430 | MSP430 | MSP430 |
| Comparators | 8 | 8 | 8 |
| DMA | 3 | 3 | 3 |
| Featured | f5 | f5 | f5 |
| Frequency, MHz | 25 | 25 | 25 |
| GPIO Pins | 47 | 47 | 47 |
| I2C | 2 | 2 | 2 |
| Max VCC | 3.6 | 3.6 | 3.6 |
| Min VCC | 1.8 | 1.8 | 1.8 |
| Multiplier | 32x32 | 32x32 | 32x32 |
| Non-volatile Memory, KB | 32 | 32 | 32 |
| Operating Temperature Range, C | -40 to 85 | -40 to 85 | -40 to 85 |
| Package Group | VQFN | BGA MICROSTAR JUNIOR | BGA MICROSTAR JUNIOR |
| Package Size: mm2:W x L, PKG | 64VQFN: 81 mm2: 9 x 9(VQFN) | 80BGA MICROSTAR JUNIOR: 25 mm2: 5 x 5(BGA MICROSTAR JUNIOR) | 80BGA MICROSTAR JUNIOR: 25 mm2: 5 x 5(BGA MICROSTAR JUNIOR) |
| RAM, KB | 6 | 6 | 6 |
| Rating | Catalog | Catalog | Catalog |
| SPI | 4 | 4 | 4 |
| Special I/O | N/A | N/A | N/A |
| Standby Power, LPM3-uA | 2.5 | 2.5 | 2.5 |
| Timers - 16-bit | 4 | 4 | 4 |
| UART | 2 | 2 | 2 |
| Wakeup Time, us | 3.5 | 3.5 | 3.5 |
生态计划
| MSP430F5513IRGCR | MSP430F5513IZQE | MSP430F5513IZQER | |
|---|---|---|---|
| RoHS | Compliant | Compliant | Compliant |
应用须知
- Implementing a Thermocouple Interface With ADC12_APDF, 105 Kb, 档案已发布: Jul 19, 2011
This application report shows how to implement a single-chip thermocouple interface. The thermocouple interfaces with the MSP430F5529’s integrated 12-bit analog/digital converter (ADC12_A) through an operational amplifier circuit. The MSP430 encodes the thermocouple readings into a digital value, converts them to temperature, and stores them in memory. - Capacitive Touch Sensing and SYS/BIOSPDF, 324 Kb, 档案已发布: Sep 12, 2012
SYS/BIOS is designed for use in embedded applications that need real-time scheduling, synchronization, and instrumentation. It provides preemptive multitasking, hardware abstraction, and memory management.This application report uses an adaptation of the capacitive touch library to interface with SYS/BIOS. Thisinterface abstracts the capacitive touch interface, promoting use of the graphical c - Multiple Time Bases on a Single MSP430 Timer Module (Rev. A)PDF, 143 Kb, 修订版: A, 档案已发布: Mar 27, 2015
The timer modules on MSP430в„ў ultra-low power microcontrollers often base several different outputs off of a single time base – a single timer period. This is especially true for the typical implementation of pulse width modulation (PWM) signals on the MSP430 devices, where one capture compare register (TxCCR0) sets the period, and the rest (TxCCRx) simply set different duty cycles. However, in som - USB Field Firmware Updates on MSP430 MCUs (Rev. C)PDF, 741 Kb, 修订版: C, 档案已发布: Nov 12, 2014
The USB solution for MSP430в„ў microcontrollers has been designed to make this process simple and straightforward. The device contains a USB-based on-chip bootstrap loader, and TI provides a Windows source project for downloading firmware that can be quickly customized. This source can be built with Visual C++ 2008 Express, available from Microsoft at no cost. For the USB support software for MSP430 - Starting a USB Design Using MSP430 MCUs (Rev. A)PDF, 949 Kb, 修订版: A, 档案已发布: May 30, 2014
This document is a high-level starting point for those wanting to design USB devices with MSP430в„ў MCUs. It provides an overview of the TI MSP430 hardware and software offerings for USB, as well as guidance in quickly getting started.Among the topics covered:An overview of the MSP430 hardware USB moduleAn introduction to the MSP430 USB Developer's Package - Using the USCI I2C Master (Rev. A)PDF, 69 Kb, 修订版: A, 档案已发布: Mar 11, 2015
This document describes how to use the I2C master function set for MSP430в„ў devices with the USCI module. These functions can be used by MSP430 master devices to ensure proper initialization of the USCI module and provide I2C transmit and receive functionality. A similar version with DMA support has also been included. The USCI I2C master function set only supports single-master transmitter or rece - Features of the MSP430F5xx Bootstrap Loader (BSL) (Rev. C)PDF, 30 Kb, 修订版: C, 档案已发布: Feb 9, 2009
This application report has been superseded by the MSP430 Memory Programming User’s Guide (SLAU265). All information previously contained in this application report can be found in the user’s guide by clicking on the following links.Download MSP430 Memory Programming User's Guide (PDF)Download associate - Using the MSP430 Timer_D Module in Hi-Resolution ModePDF, 870 Kb, 档案已发布: Oct 2, 2013
This application report describes the use of the high-resolution feature of the Timer_D module introduced in MSP430F51x1 and MSP430F51x2 devices. Timer_D enables applications that require high resolution such as capacitive touch detection, PWM DACs, advanced LED lighting, and digital controllers for power supplies. This application report provides an advanced description of the use and calibration - MSP430x5xx Quick Start GuidePDF, 118 Kb, 档案已发布: Jun 5, 2008
This quick start guide is intended to assist existing users of the MSP430 line of products in converting existing code to the new MSP430x5xx modules. While the modules operate in accordance with previous families, the MSP430x5xx modules include a number of enhancements which allow for more effective coding, expansions on current functionality and greater flexibility in the module and system operat - MSP430x5xx Overview Comparison to MSP430x2xx and MSP430x4xxPDF, 81 Kb, 档案已发布: Jun 5, 2008
The MSP430x5xx series of devices is the latest addition to the MSP430 family of microcontrollers. Although there are many common features between the MSP430x5xx and MSP430x2xx/MSP430x4xx offerings, there are also several differences. This document gives a brief overview of differences between the device families. Detailed information regarding specific differences can be found in the respective mo - Migrating from the MSP430F5xx,F6xx Family to the MSP430FR58xx/FR59xx/68xx Family (Rev. D)PDF, 151 Kb, 修订版: D, 档案已发布: Nov 3, 2016
This application report helps enable easy migration from MSP430F5xx and MSP430F6xx flash-based MCUs to the MSP430FR58xx/FR59xx/68xx/69xx FRAM-based MCUs. For the migration guide to MSP430FR57xx, see Migrating From the MSP430F2xx Family to the MSP430FR57xx Family. It covers programming, system, and peripheral considerations when migrating firmware. The intent is to highlight differences between the - Spread-Spectrum Clock Source Using an MSP430PDF, 228 Kb, 档案已发布: May 31, 2006
While spread-spectrum clocking has long since been used in processor and memory clock trees, there are many other clocked systems, such as power supplies or switch-mode amplifiers, that continue to use a single-frequency clock. This can, in turn, generate significant EMI and can make meeting governmental regulations for EMI challenging. These regulations typically set a limit on peak energy within - Current Transformer Phase Shift Compensation and CalibrationPDF, 63 Kb, 档案已发布: Jan 30, 2001
This application report demonstrates a digital technique to compensate and calibrate the phase shift of a current (or voltage) transformer used in electric power of energy measurement. Traditional analog compensation is replaced by a digital finite impulse response (FIR) filter. A technique emulating a non-unity power factor (non-UPF) load makes the calibration fully automatic. The calibration tim - MSP430 Isolated FET InterfacePDF, 1.2 Mb, 档案已发布: Oct 10, 2003
This application report describes how to build an isolated FET interface for the MSP430 Flash Emulation Tool (FET). When developing and debugging line-powered MSP430applications such as motor control, electricity energy meters, power monitoring systems etc. it is important to have electrical isolation for the development tool such that the personnel involved and the connected electronic equipmen - HDQ Protocol Implementation with MSP430PDF, 124 Kb, 档案已发布: Feb 19, 2004
- Economic Voltage Measurement With the MSP430 FamilyPDF, 91 Kb, 档案已发布: Oct 12, 1999
This application report describes voltage and current measurement methods using the MSP430 universal timer/port module. The report explains the two measurement methods (charge and discharge) and shows how to measure voltage and current. The equations for the calculations are also given. Further sections show additional applications such as the measurement of two voltage inputs, bridge arrangem - Generation and Recognition of DTMF Signals With the Microcontroller MSP430PDF, 233 Kb, 档案已发布: Oct 1, 1997
The first part of the Application Report describes the generation of DTMF signals using the Microcontroller MSP430. Following an explanation of the most important specifications which are involved, the theoretical and mathematical processes will be discussed with which sinusoidal waveforms can be derived from square-wave signals, by making use of appropriate analog filters. Tested examples of soft - Choosing an Ultra Low-Power MCUPDF, 306 Kb, 档案已发布: Jun 30, 2004
This application report describes how to compare ultralow-power MCUs. It discusses the key differences between popular low-power MCUs and how to interpret features and specifications and apply them to application requirements. - MSP430 LFXT1 Oscillator AccuracyPDF, 184 Kb, 档案已发布: Nov 15, 2004
This report details the factors that influence achievable accuracy of the low frequency oscillator, specifically for real-time clock (RTC) applications. The intent of this application report is to provide an understanding of MSP430-specific factors influencing real-world achievable RTC accuracy using the LFXT1 oscillator with a standard 32.768 kHz watch crystal and present measurement data support - MSP430 Family Mixed-Signal Microcontroller Application ReportsPDF, 5.5 Mb, 档案已发布: Jan 21, 2000
MSP430 Metering Application Report - Simple 1.5 V Boost Converter for MSP430PDF, 49 Kb, 档案已发布: Oct 18, 2000
A simple, efficient, low-cost, boost converter to take 1.5 V from a single type-AA alkaline battery to the operating voltage required by the MSP430 family of ultralow-power microcontrollers is described. Expected battery life is up to 1000 hours. - FSK Modulation and Demodulation With the Microcontroller MSP430PDF, 110 Kb, 档案已发布: Dec 14, 1998
This application report describes a software program for performing V.23 FSK modem transceiver functions using an MSP430 microcontroller. It makes use of novel filter architecture to perform DSP functions on a processor with only shift and add capabilities. - Wave Digital Filtering Using the MSP430PDF, 220 Kb, 档案已发布: Sep 13, 2006
Digital filtering is an integral part of many digital signal processing algorithms. Digital filters are characterized as either recursive [infinite impulse response (IIR)] or non-recursive [finite impulse response (FIR)] filters. IIR filters require a smaller order for the same set of specifications compared to FIR filters, while FIR filters provide a linear phase property. However, IIR filters, i - CRC Implementation with MSP430PDF, 125 Kb, 档案已发布: Nov 4, 2004
Cyclic Redundancy Code (CRC) is commonly used to determine the correctness of a data transmission or storage. This application note presents a solution to compute 16-bit and 32-bit CRCs on the ultra low-power TI MSP430 microcontroller for the bitwise algorithm (low memory, low cost) and the table-based algorithm (low MIPS, low power). Both algorithms are presented in C and MSP430 assembly. Test co - Mixing C and Assembler with the MSP430PDF, 168 Kb, 档案已发布: Feb 28, 2002
This application note describes how C and assembler code can be used together within an MSP430 application. The combination of C and assembler benefits the designer by providing the power of a high-level language as well as the speed, efficiency, and low-level control of assembler. - Random Number Generation Using the MSP430PDF, 39 Kb, 档案已发布: Oct 13, 2006
Many applications require the generation of random numbers. These random numbers are useful for applications such as communication protocols, cryptography, and device individualization.Generating random numbers often requires the use of expensive dedicated hardware. Using the two independent clocks available on the MSP430F2xx family of devices, it is possible to generate random numbers without s - Efficient Multiplication and Division Using MSP430PDF, 104 Kb, 档案已发布: Aug 3, 2006
- Interfacing the MSP430 and TLC549/1549 A/D ConvertersPDF, 44 Kb, 档案已发布: Nov 16, 2000
This application report describes how to interface an MSP430 mixed-signal microcontroller with the TLC549 and TLV1549 3-volt A/D converters. This report is written for the MSP430x11x(1) family, but can be adapted to any MSP430 derivative. - Interfacing TMS320C5000 DSP to MSP430 Mixed Signal Microcontroller (Rev. A)PDF, 82 Kb, 修订版: A, 档案已发布: Oct 13, 2000
The TMS320C5000в„ў family of digital signal processors (DSPs) features Host Port Interface Controllers (HPI) and Direct Memory Access Controllers (DMAC) for efficient data movement without any CPU involvement. The HPI enables the DSP to interface to host processors (typically microcontrollers) bidirectionally with minimal or no external interface logic. This application report presents a hardw - MSP430 Capacitive Single-Touch Sensor Design GuidePDF, 770 Kb, 档案已发布: Jan 16, 2008
This application report discusses the design of RC-type capacitive single-touch sensors using the MSP430 microcontroller. The MSP430 has some unique features that make it suitable for interfacing with capacitive-touch sensors. The RC-type method does not need special peripherals and can be implemented with all devices in the MSP430 product family. This method is also inherently low power and can - Programming a Flash-Based MSP430 Using the JTAG Interface (Rev. H)