Datasheet Texas Instruments MSP430FG4618 — 数据表
制造商 | Texas Instruments |
系列 | MSP430FG4618 |
16位超低功耗MCU,116KB闪存,8KB RAM,12位ADC,双DAC,DMA,3个OPAMP,160段LCD
数据表
MSP430FG461x, MSP430CG461x Mixed-Signal Microcontrollers datasheet
PDF, 2.2 Mb, 修订版: J, 档案已发布: Jun 19, 2015
从文件中提取
价格
状态
MSP430FG4618IPZ | MSP430FG4618IPZR | MSP430FG4618IZQW | MSP430FG4618IZQWR | MSP430FG4618IZQWT | |
---|---|---|---|---|---|
Lifecycle Status | Active (Recommended for new designs) | Active (Recommended for new designs) | Active (Recommended for new designs) | Active (Recommended for new designs) | Active (Recommended for new designs) |
Manufacture's Sample Availability | Yes | Yes | No | No | No |
打包
MSP430FG4618IPZ | MSP430FG4618IPZR | MSP430FG4618IZQW | MSP430FG4618IZQWR | MSP430FG4618IZQWT | |
---|---|---|---|---|---|
N | 1 | 2 | 3 | 4 | 5 |
Pin | 100 | 100 | 113 | 113 | 113 |
Package Type | PZ | PZ | ZQW | ZQW | ZQW |
Industry STD Term | LQFP | LQFP | BGA MICROSTAR JUNIOR | BGA MICROSTAR JUNIOR | BGA MICROSTAR JUNIOR |
JEDEC Code | S-PQFP-G | S-PQFP-G | S-PBGA-N | S-PBGA-N | S-PBGA-N |
Package QTY | 90 | 1000 | 250 | 2500 | 250 |
Carrier | JEDEC TRAY (5+1) | LARGE T&R | JEDEC TRAY (5+1) | LARGE T&R | SMALL T&R |
Device Marking | M430FG4618 | M430FG4618 | M430FG4618 | M430FG4618 | M430FG4618 |
Width (mm) | 14 | 14 | 7 | 7 | 7 |
Length (mm) | 14 | 14 | 7 | 7 | 7 |
Thickness (mm) | 1.4 | 1.4 | .74 | .74 | .74 |
Pitch (mm) | .5 | .5 | .5 | .5 | .5 |
Max Height (mm) | 1.6 | 1.6 | 1 | 1 | 1 |
Mechanical Data | 下载 | 下载 | 下载 | 下载 | 下载 |
参数化
Parameters / Models | MSP430FG4618IPZ | MSP430FG4618IPZR | MSP430FG4618IZQW | MSP430FG4618IZQWR | MSP430FG4618IZQWT |
---|---|---|---|---|---|
ADC | ADC12 - 12ch | ADC12 - 12ch | ADC12 - 12ch | ADC12 - 12ch | ADC12 - 12ch |
AES | N/A | N/A | N/A | N/A | N/A |
Active Power, uA/MHz | 400 | 400 | 400 | 400 | 400 |
Additional Features | LCD,Real-Time Clock,Watchdog,OpAmp,Temp Sensor,Brown Out Reset | LCD,Real-Time Clock,Watchdog,OpAmp,Temp Sensor,Brown Out Reset | LCD,Real-Time Clock,Watchdog,OpAmp,Temp Sensor,Brown Out Reset | LCD,Real-Time Clock,Watchdog,OpAmp,Temp Sensor,Brown Out Reset | LCD,Real-Time Clock,Watchdog,OpAmp,Temp Sensor,Brown Out Reset |
BSL | UART | UART | UART | UART | UART |
CPU | MSP430 | MSP430 | MSP430 | MSP430 | MSP430 |
Comparators | Yes | Yes | Yes | Yes | Yes |
DMA | 3 | 3 | 3 | 3 | 3 |
Frequency, MHz | 8 | 8 | 8 | 8 | 8 |
GPIO Pins | 80 | 80 | 80 | 80 | 80 |
I2C | 1 | 1 | 1 | 1 | 1 |
Max VCC | 3.6 | 3.6 | 3.6 | 3.6 | 3.6 |
Min VCC | 1.8 | 1.8 | 1.8 | 1.8 | 1.8 |
Multiplier | 16x16 | 16x16 | 16x16 | 16x16 | 16x16 |
Non-volatile Memory, KB | 116 | 116 | 116 | 116 | 116 |
Operating Temperature Range, C | -40 to 85 | -40 to 85 | -40 to 85 | -40 to 85 | -40 to 85 |
Package Group | LQFP | LQFP | BGA MICROSTAR JUNIOR | BGA MICROSTAR JUNIOR | BGA MICROSTAR JUNIOR |
Package Size: mm2:W x L, PKG | 100LQFP: 256 mm2: 16 x 16(LQFP) | 100LQFP: 256 mm2: 16 x 16(LQFP) | 113BGA MICROSTAR JUNIOR: 49 mm2: 7 x 7(BGA MICROSTAR JUNIOR) | 113BGA MICROSTAR JUNIOR: 49 mm2: 7 x 7(BGA MICROSTAR JUNIOR) | 113BGA MICROSTAR JUNIOR: 49 mm2: 7 x 7(BGA MICROSTAR JUNIOR) |
RAM, KB | 8 | 8 | 8 | 8 | 8 |
Rating | Catalog | Catalog | Catalog | Catalog | Catalog |
SPI | 1 | 1 | 1 | 1 | 1 |
Special I/O | N/A | N/A | N/A | N/A | N/A |
Standby Power, LPM3-uA | 1.3 | 1.3 | 1.3 | 1.3 | 1.3 |
Timers - 16-bit | 2 | 2 | 2 | 2 | 2 |
UART | 1 | 1 | 1 | 1 | 1 |
Wakeup Time, us | 6 | 6 | 6 | 6 | 6 |
生态计划
MSP430FG4618IPZ | MSP430FG4618IPZR | MSP430FG4618IZQW | MSP430FG4618IZQWR | MSP430FG4618IZQWT | |
---|---|---|---|---|---|
RoHS | Compliant | Compliant | Compliant | Compliant | Compliant |
应用须知
- Low-Cost Speech With MSP430 (Rev. A)PDF, 386 Kb, 修订版: A, 档案已发布: Sep 14, 2009
This application report describes the implementation of a low-cost solution to store and play audio or polyphone ringtones with an MSP430. The best solution for flexible and low-cost audio playback is chosen using a demonstration board that is based on the MSP430 USB Stick Development Tool and the MSP430FG4618 Experimenter Board. - Using power solutions to extend battery life in MSP430 applicationsPDF, 538 Kb, 档案已发布: Oct 4, 2009
- Clear Channel Assessment Using TI MSP430 and CC2500 RadioPDF, 950 Kb, 档案已发布: Jul 31, 2007
This application report describes a 2.4-GHz anti-jamming frequency-hopping system consisting of a designated Transmitter and Receiver, each with distinct functions to avoid RF-channel interference. The Transmitter board emulates the control device (e.g., remote control) by sending commands to be processed on the Receiver side (e.g., TV, stereo, set top box, or gaming console). Since many popular c - PMBus Implementation Using the MSP430 USCI (Rev. A)PDF, 187 Kb, 修订版: A, 档案已发布: Feb 5, 2008
This document provides an example application for the Power Management Bus (PMBus) protocol implementation using the MSP430 as a master PMBus device. The PMBus protocol is an open-standard power-management protocol used for communicating with power conversion devices. It is implemented using the popular I2C communication protocol at a hardware level and is controlled by a software interface of PMB - Extended Memory Access Using IAR v3.42A and CCE v2PDF, 205 Kb, 档案已发布: Nov 7, 2007
This application report describes how to access the extended memory in devices with memory greater than 64 KB using the large code/small data model supported by the IAR C/C++ compiler v3.42A and Code Composer Essentials (CCE) v2. The purpose of this application report is to provide an understanding of the extended features of the MSP430X CPU, customizing the linker command file to fit the target s - Q4 2009 Issue Analog Applications JournalPDF, 1.5 Mb, 档案已发布: Oct 4, 2009
- Implementing a Direct Thermocouple Interface With MSP430x4xx and ADS1240 (Rev. A)PDF, 195 Kb, 修订版: A, 档案已发布: Oct 4, 2001
This application report describes and shows how to implement a direct thermocouple interface, without using the signal conditioning circuitry normally required for thermocouples. The thermocouple interfaces directly to the Burr Brown ADS1240, 24-bit ADC from Texas Instruments, Inc. An MSP430F41x ultralow-power microcontroller is used to communicate with the ADC, read the conversion values, convert - MSP430 Embedded Application Binary InterfacePDF, 596 Kb, 档案已发布: May 16, 2012
This document is a specification for the ELF-based Embedded Application Binary Interface (EABI) for the MSP430 family of processors from Texas Instruments. The EABI defines the low-level interface between programs, program components, and the execution environment, including the operating system if one is present. Components of the EABI include calling conventions, data layout and addressing conve - Designing With MSP430 and Segment LCDs (Rev. A)PDF, 2.1 Mb, 修订版: A, 档案已发布: Jul 20, 2015
Segment liquid crystal displays (LCDs) are needed to provide information to users in a wide variety of applications from smart meters to electronic shelf labels (ESL) to medical equipment. Several MSP430в„ў microcontroller families include built-in low-power LCD driver circuitry that allows the MSP430 MCU to directly control the segmented LCD glass. This application note helps explain how segmented - HDQ Protocol Implementation with MSP430PDF, 124 Kb, 档案已发布: Feb 19, 2004
- MSP430 Isolated FET InterfacePDF, 1.2 Mb, 档案已发布: Oct 10, 2003
This application report describes how to build an isolated FET interface for the MSP430 Flash Emulation Tool (FET). When developing and debugging line-powered MSP430applications such as motor control, electricity energy meters, power monitoring systems etc. it is important to have electrical isolation for the development tool such that the personnel involved and the connected electronic equipmen - Current Transformer Phase Shift Compensation and CalibrationPDF, 63 Kb, 档案已发布: Jan 30, 2001
This application report demonstrates a digital technique to compensate and calibrate the phase shift of a current (or voltage) transformer used in electric power of energy measurement. Traditional analog compensation is replaced by a digital finite impulse response (FIR) filter. A technique emulating a non-unity power factor (non-UPF) load makes the calibration fully automatic. The calibration tim - Spread-Spectrum Clock Source Using an MSP430PDF, 228 Kb, 档案已发布: May 31, 2006
While spread-spectrum clocking has long since been used in processor and memory clock trees, there are many other clocked systems, such as power supplies or switch-mode amplifiers, that continue to use a single-frequency clock. This can, in turn, generate significant EMI and can make meeting governmental regulations for EMI challenging. These regulations typically set a limit on peak energy within - Generation and Recognition of DTMF Signals With the Microcontroller MSP430PDF, 233 Kb, 档案已发布: Oct 1, 1997
The first part of the Application Report describes the generation of DTMF signals using the Microcontroller MSP430. Following an explanation of the most important specifications which are involved, the theoretical and mathematical processes will be discussed with which sinusoidal waveforms can be derived from square-wave signals, by making use of appropriate analog filters. Tested examples of soft - Economic Voltage Measurement With the MSP430 FamilyPDF, 91 Kb, 档案已发布: Oct 12, 1999
This application report describes voltage and current measurement methods using the MSP430 universal timer/port module. The report explains the two measurement methods (charge and discharge) and shows how to measure voltage and current. The equations for the calculations are also given. Further sections show additional applications such as the measurement of two voltage inputs, bridge arrangem - Choosing an Ultra Low-Power MCUPDF, 306 Kb, 档案已发布: Jun 30, 2004
This application report describes how to compare ultralow-power MCUs. It discusses the key differences between popular low-power MCUs and how to interpret features and specifications and apply them to application requirements. - MSP430 LFXT1 Oscillator AccuracyPDF, 184 Kb, 档案已发布: Nov 15, 2004
This report details the factors that influence achievable accuracy of the low frequency oscillator, specifically for real-time clock (RTC) applications. The intent of this application report is to provide an understanding of MSP430-specific factors influencing real-world achievable RTC accuracy using the LFXT1 oscillator with a standard 32.768 kHz watch crystal and present measurement data support - MSP430 Family Mixed-Signal Microcontroller Application ReportsPDF, 5.5 Mb, 档案已发布: Jan 21, 2000
MSP430 Metering Application Report - Simple 1.5 V Boost Converter for MSP430PDF, 49 Kb, 档案已发布: Oct 18, 2000
A simple, efficient, low-cost, boost converter to take 1.5 V from a single type-AA alkaline battery to the operating voltage required by the MSP430 family of ultralow-power microcontrollers is described. Expected battery life is up to 1000 hours. - Wave Digital Filtering Using the MSP430PDF, 220 Kb, 档案已发布: Sep 13, 2006
Digital filtering is an integral part of many digital signal processing algorithms. Digital filters are characterized as either recursive [infinite impulse response (IIR)] or non-recursive [finite impulse response (FIR)] filters. IIR filters require a smaller order for the same set of specifications compared to FIR filters, while FIR filters provide a linear phase property. However, IIR filters, i - FSK Modulation and Demodulation With the Microcontroller MSP430PDF, 110 Kb, 档案已发布: Dec 14, 1998
This application report describes a software program for performing V.23 FSK modem transceiver functions using an MSP430 microcontroller. It makes use of novel filter architecture to perform DSP functions on a processor with only shift and add capabilities. - CRC Implementation with MSP430PDF, 125 Kb, 档案已发布: Nov 4, 2004
Cyclic Redundancy Code (CRC) is commonly used to determine the correctness of a data transmission or storage. This application note presents a solution to compute 16-bit and 32-bit CRCs on the ultra low-power TI MSP430 microcontroller for the bitwise algorithm (low memory, low cost) and the table-based algorithm (low MIPS, low power). Both algorithms are presented in C and MSP430 assembly. Test co - Mixing C and Assembler with the MSP430PDF, 168 Kb, 档案已发布: Feb 28, 2002
This application note describes how C and assembler code can be used together within an MSP430 application. The combination of C and assembler benefits the designer by providing the power of a high-level language as well as the speed, efficiency, and low-level control of assembler. - Random Number Generation Using the MSP430PDF, 39 Kb, 档案已发布: Oct 13, 2006
Many applications require the generation of random numbers. These random numbers are useful for applications such as communication protocols, cryptography, and device individualization.Generating random numbers often requires the use of expensive dedicated hardware. Using the two independent clocks available on the MSP430F2xx family of devices, it is possible to generate random numbers without s - Efficient Multiplication and Division Using MSP430PDF, 104 Kb, 档案已发布: Aug 3, 2006
- General Oversampling of MSP ADCs for Higher Resolution (Rev. A)PDF, 551 Kb, 修订版: A, 档案已发布: Apr 1, 2016
Multiple MSP ultra-low-power microcontrollers offer analog-to-digital converters (ADCs) to convert physical quantities into digital numbers, a function that is widely used across numerous applications. There are times, however, when a customer design demands a higher resolution than the ADC of the selected MSP can offer. This application report, which is based on the previously-published Oversampl - Interfacing the MSP430 and TLC549/1549 A/D ConvertersPDF, 44 Kb, 档案已发布: Nov 16, 2000
This application report describes how to interface an MSP430 mixed-signal microcontroller with the TLC549 and TLV1549 3-volt A/D converters. This report is written for the MSP430x11x(1) family, but can be adapted to any MSP430 derivative. - Interfacing TMS320C5000 DSP to MSP430 Mixed Signal Microcontroller (Rev. A)PDF, 82 Kb, 修订版: A, 档案已发布: Oct 13, 2000
The TMS320C5000в„ў family of digital signal processors (DSPs) features Host Port Interface Controllers (HPI) and Direct Memory Access Controllers (DMAC) for efficient data movement without any CPU involvement. The HPI enables the DSP to interface to host processors (typically microcontrollers) bidirectionally with minimal or no external interface logic. This application report presents a hardw - MSP430 Capacitive Single-Touch Sensor Design GuidePDF, 770 Kb, 档案已发布: Jan 16, 2008
This application report discusses the design of RC-type capacitive single-touch sensors using the MSP430 microcontroller. The MSP430 has some unique features that make it suitable for interfacing with capacitive-touch sensors. The RC-type method does not need special peripherals and can be implemented with all devices in the MSP430 product family. This method is also inherently low power and can - Programming a Flash-Based MSP430 Using the JTAG Interface (Rev. H)