Datasheet Linear Technology LT1114S#PBF — 数据表

数据表

价格

打包

参数化

生态计划

其他选择

LT1112 LT1112

应用须知

• 下载
  Linear Technology Magazine Circuit Collection, Volume III &mdash AN67
  PDF, 1.2 Mb, 档案已发布: Sep 1, 1996
  Application Note 67 is a collection of circuits for data conversion, interface and signal processing from the first five years of Linear Technology. This application note includes circuits such as fast video multiplexers for high speed video, an ultraselective bandpass filter circuit with adjustable gain, and a fully differential, 8-channel, 12-bit A/D system. The categories included in this app note are data conversion, interface, filters, instrumentation, video/op amps and miscellaneous circuits.
  从文件中提取

  Application Note 67
  September 1996
  Linear Technology Magazine Circuit Collection, Volume III
  Data Conversion, Interface and Signal Processing
  Richard Markell, Editor
  INTRODUCTION
  Application Note 67 is a collection of circuits from the first
  five years of Linear Technology, targeting data conversion,
  interface and signal processing applications. This
  Application Note includes circuits such as fast video
  multiplexers for high speed video, an ultraselective
  bandpass filter circuit with adjustable gain and a fully differential, 8-channel, 12-bit A/D system. The categories
  included herein are data conversion, interface, filters,
  instrumentation, video/op amps and miscellaneous
  circuits. Application Note 66, which covers power products
  and circuits from Linear Technology ’s first five years, is
  also available from LTC. ARTICLE INDEX
  Data Conversion . 3
  Fully Differential, 8-Channel, 12-Bit A/D System Using the LTCВ®1390 and LTC1410 . 3
  12-Bit DAC Applications . 5
  LTC1329 Micropower, 8-Bit, Current Output DAC Used for Power Supply Adjustment,
  Trimmer Pot Replacement . 7
  12-Bit Cold Junction Compensated, Temperature Control System with Shutdown . 8 …

设计须知

• 下载
  C-Load TM Op Amps Conquer Instabilities &mdash DN107
  PDF, 495 Kb, 档案已发布: Jul 1, 1995
  从文件中提取

  C-Load Op Amps Conquer Instabilities – Design Note 107
  Kevin R. Hoskins
  Introduction
  Linear Technology Corporation has taken advantage of
  advances in process technology and circuit innovations
  to create a series of C-Loadв„ў operational amplifiers that
  are tolerant of capacitive loading, including the ultimate,
  amplifiers that remain stable driving any capacitive load.
  This series of amplifiers has a bandwidth that ranges from
  160kHz to 140MHz. These amplifiers are appropriate for
  a wide range of applications from coaxial cable drivers to
  analog-to-digital converter (ADC) input buffer/amplifiers.
  Driving ADCs
  Most contemporary ADCs incorporate a sample-and-hold
  (S/H). A typical S/H circuit is shown in Figure 1. The hold
  capacitor’s (C1) size varies with the ADC’s resolution but
  is generally in the range of 5pF to 20pF, 10pF to 30pF and
  10pF to 50pF for 8-, 10-and 12-bit ADCs, respectively. gracefully and accurately drive capacitive loads, such as
  Linear Technology’s C-Load line of monolithic amplifiers.
  Table 1 lists Linear Technology’s unconditionally stable
  voltage feedback C-Load amplifiers. Table 2 lists other
  voltage feedback C-Load amplifiers that are stable with
  loads up to 10,000pF. …

• 下载
  C-Load TM Op Amps Tame Instabilities &mdash DN83
  PDF, 929 Kb, 档案已发布: Jun 1, 1994
  从文件中提取

  C-Load Op Amps Tame Instabilities – Design Note 83
  Richard Markell, George Feliz and William Jett
  Introduction
  By taking advantage of advances in process technology
  and innovative circuit design, Linear Technology Corporation has developed a series of C-Loadв„ў op amps which
  are tolerant of capacitive loading, including the ultimate,
  amplifiers which are stable with any capacitive load. These
  amplifiers span a range of bandwidths from 1MHz to
  140MHz. They are suited for a wide range of applications
  from coaxial cable drivers to capacitive transducer exciters.
  The Problem
  The cause of the capacitive load stability problem in most
  amplifiers is the pole formed by the load capacitance and
  the open-loop output impedance of the amplifier. This
  output pole increases the phase lag around the loop which
  reduces the phase margin of the amplifier. If the phase
  lag is great enough the amplifier will oscillate.
  External networks can be used to improve the amplifier’s
  stability with a capacitive load but have serious drawbacks.
  For instance, most designers are familiar with the use of
  a series resistor RS between the load and the amplifier
  output. The optimum value of RS depends on the load
  capacitance, so this approach isn’t useful for ill-defined …

文章

• 下载
  The LT1167: Precision, Low Cost, Low Power Instrumentation Amplifier Requires a Single Gain-Set Resistor &mdash LT Journal
  PDF, 294 Kb, 档案已发布: May 1, 1998
  从文件中提取

  DESIGN FEATURES The LT1167: Precision, Low Cost,
  Low Power Instrumentation Amplifier
  Requires a Single Gain-Set Resistor
  by Alexander Strong
  Introduction Input Protection The LT1167 is the next-generation
  instrumentation amplifier designed
  to replace the previous generation of
  monolithic instrumentation amps, as
  well as discrete, multiple op amp
  solutions. Instrumentation amplifiers differ from operational amplifiers
  in that they can amplify input signals
  that are not ground referenced. The
  output of an instrumentation amplifier is referenced to an external voltage
  that is independent of the input. Conversely, the output voltage of an op
  amp, due to the nature of its feedback, is referenced to the differential
  and common mode input voltage.
  A separate ground reference and
  the high CMRR of the LT1167 instrumentation amplifier reduce the effect
  of the input common mode voltage on
  the output signal. The closed-loop
  gain of an op amp and of most instrumentation amps is set by a resistor
  ratio; the gain of the LT1167 is set by
  the absolute value of one external …

• 下载
  Consider New Precision Amplifiers for Updated Industrial Equipment Designs &mdash LT Journal
  PDF, 154 Kb, 档案已发布: Sep 1, 2009
  从文件中提取

  L DESIGN FEATURES Consider New Precision Amplifiers for
  Updated Industrial Equipment Designs
  by Brian Black Introduction
  Industrial equipment is designed for
  long life cycles, so the electronic components used in industrial applications
  are often chosen with significant emphasis on proven performance, quality
  and reliability. Precision amplifiers are
  no exception. Even if new and innovative amplifiers become available over a
  product’s lifetime, a redesigned board
  is often built using the same proven
  op amps in the old board. Even for
  entirely new applications, designers
  will choose amplifiers that have proven
  their mettle in other circuits, making a
  choice based more on familiarity than
  performance.
  Although an amplifier may have
  been tried and proven in a design, it
  is not necessarily the best solution for
  every new design. Many can benefit
  from using more recently released
  amplifiers, which can improve overall
  system performance, reduce power …

模型线

制造商分类

• Signal Conditioning > Amplifiers > Operational Amplifiers (Op Amps) > High Voltage Amplifiers (>12V) | Precision Amplifiers (Vos | Low Power Amplifiers (Is < 1mA/amp) | Low Bias Current Amplifiers (Ib < 100pA)

其他名称:

LT1114SPBF, LT1114S PBF