Datasheet Linear Technology LT1180ACSW#PBF — 数据表

数据表

价格

打包

参数化

生态计划

其他选择

LT1181A

应用须知

• 下载
  Data Acquisition Circuit Collection &mdash AN62
  PDF, 349 Kb, 档案已发布: Oct 1, 1994
  This application note presents a wide variety of data acquisition circuits. The detailed circuit schematics cover 8-, 10-, and 12- bit ADC and DAC applications, serial and parallel digital interfaces, battery monitoring, temperature sensing, isolated interfaces, and connections to various popular microprocessors and microcontrollers. An appendix covers suggested voltage references.
  从文件中提取

  Application Note 62
  October 1994
  Data Acquisition Circuit Collection
  Kevin R. Hoskins
  INTRODUCTION
  This application note features 8-, 10-, and 12-bit data
  acquisition components in various circuit configurations.
  The circuits include battery monitoring, temperature sensing, isolated serial interfaces, and microprocessor and
  microcontroller serial and parallel interfaces. Also included are voltage reference circuits (Application Note 42
  contains more voltage reference circuits). Additional circuit information is located in the information
  references listed in the Circuit Index. Each information
  reference refers to either an application note (example:
  AN42 = Application Note 42), a data sheet (example:
  LTCВ®1292 DS = LTC1292 Data Sheet), or a design note
  (example: DN66 = Design Note 66).
  and LTC are registered trademarks and LT is a trademark of Linear Technology Corporation. CIRCUIT INDEX
  FIGURE TITLE
  FIGURE NO.
  General Analog-to-Digital Application Circuits
  Two-Quadrant 150kHz Bandwidth Analog Multiplier . Figure 1 .
  Infinite Hold-Time Sample-and-Hold (tACQ = 240ns) . Figure 2 .
  Four-Quadrant 250kHz Bandwidth Analog Multiplier . Figure 3 .
  Demodulating a Signal Using Undersampling . Figure 4 . …

设计须知

• 下载
  Extending the Applications of 5V Powered RS232 Transceivers &mdash DN14
  PDF, 102 Kb, 档案已发布: Sep 1, 1988
  从文件中提取

  Extending the Applications of 5V Powered RS232 Transceivers
  Design Note 14 High Speed Operation
  Although the EIA RS232 specification is for a relatively
  slow communications protocol, many applications
  require RS232 transceivers to operate at higher frequencies. Devices such as the LTВ®1080, LT1081, and the
  LT1130 series share a common design for the drivers
  and receivers and are capable of operating over 100
  kilobaud.
  Although the slew rate is controlled for all of the Linear
  Technology series of RS232 communications devices,
  for output levels limited to В±6V the transition time is
  fast enough to allow high baud rates. With a slew rate
  of approximately 10V per microsecond, it only takes
  1.2 microseconds for a 12V excursion. The two photos
  (Figure 1 and Figure 2) show the output waveform and
  delay associated with a 75kHz square wave input and a
  100kHz square wave. Delay times are in the order of 0.5
  microseconds and the total slew time is approximately 1.2 microseconds. Output load is 3k. Receivers are
  much faster and can handle these baud rates with no
  problem. For higher communication rates, a differential
  signal is recommended.
  Power Supply Tricks
  The power supply generator on 5V powered devices is …

• 下载
  Design Considerations for RS-232 Interfaces &mdash DN27
  PDF, 319 Kb, 档案已发布: Oct 1, 1989
  从文件中提取

  Design Considerations for RS232 Interfaces
  Design Note 27
  Sean Gold Table 1. Key RS232 Transceiver Specifications
  (EIA RS232C.V28)
  SPECIFICATIONS
  Signal Levels
  Cable Length
  Load Capacitance
  Cable Termination
  Data Rate
  Slew Rate
  Fault Conditions VALUE
  В±15 Max; В±5 Min
  50 Max
  2500 Max
  3k < R < 7k
  20k Max
  3 < SR < 30
  Drivers Must Tolerate: Conductor to Conductor Shorts Line Open Circuit В±25V Line Overage UNITS
  V
  Ft
  pF
  О© …

• 下载
  A Single Supply RS232 Interface for Bipolar A to D Converters &mdash DN29
  PDF, 455 Kb, 档案已发布: Dec 1, 1989
  从文件中提取

  A Single Supply RS232 Interface for Bipolar A to D Converters
  Design Note 29
  Sean Gold
  system. Construction also requires close attention to the
  layout of the system grounds and other aspects of circuit
  board design to avoid noise problems.2 Designing circuitry for single supply operation is often an
  attractive simplification for reducing production costs. Yet
  many applications call for just a few additional supplies to
  solve simple interface problems. The example presented
  here describes how an advanced RS232 interface can simplify an A to D converter which processes bipolar signals. To accommodate bipolar inputs (–5 < VIN < 5), the
  LTC1094’s negative rail must be biased beyond the extreme
  signal swing, but below absolute maximum ratings for
  supplies. A 5.6V Zener diode, D1, provides a sufficient
  bias because the V– pin draws very little current. The LT®1180 RS232 transceiver includes a charge pump
  which produces low ripple supplies with sufficient surplus
  current to drive a CMOS A to D converter and precision
  voltage reference. The circuit in Figure 1 operates from
  a single 5V supply, and draws a total quiescent current
  of only 37mA. These features make the circuit ideal for
  applications which must process bipolar signals with
  minimal support electronics. The A to D converter communicates with a remote controller via three wires, which carry the clock, the configuration
  word, and the output data. The chip select signal, CS, is
  generated from the incoming clock with a peak detector, …

• 下载
  ESD Testing for RS232 Interface Circuits &mdash DN80
  PDF, 85 Kb, 档案已发布: Mar 1, 1994
  从文件中提取

  ESD Testing for RS232 Interface Circuits – Design Note 80
  Gary Maulding
  In 1992 Linear Technology introduced the п¬Ѓrst RS232
  interface circuits capable of surviving in excess of В±10kV
  ESD transients. Since that time, LTC has introduced
  more than 30 products with this level of protection.
  The inherent ruggedness of these products eliminates
  the need to use external protection devices in most
  applications. Not one unit has been returned from the
  п¬Ѓeld to Linear Technology for an ESD related failure
  analysis since the enhanced ESD protected devices
  were introduced.
  The В±10kV ESD voltage rating is based on the Human
  Body ESD Model. When evaluated with other standard
  ESD test methods, the superior ESD ruggedness of
  LTC’s transceivers gives equally impressive results
  when compared to older conventional designs.
  The various ESD test methodologies all share a common configuration as shown in Figure 1. A source
  capacitor is п¬Ѓrst charged to a high voltage, then the
  high voltage power supply is disconnected from the
  capacitor, and the capacitor is connected to the device
  under test through a limiting resistor. The value of the
  test capacitor and the limiting resistor differ among the …

模型线

制造商分类

• Interface > RS232/RS562 Transceivers

其他名称:

LT1180ACSWPBF, LT1180ACSW PBF