Datasheet ATtiny13A. Appendix B. Specification at 125°C (Microchip) - 5
| 制造商 | Microchip |
| 描述 | 8-bit AVR Microcontroller with 1K Bytes In-System Programmable Flash |
| 页数 / 页 | 38 / 5 — ATtiny13A. 1.6. Analog Comparator Characteristics. Table 1-5. Symbol. … |
| 文件格式/大小 | PDF / 1.7 Mb |
| 文件语言 | 英语 |
ATtiny13A. 1.6. Analog Comparator Characteristics. Table 1-5. Symbol. Parameter. Condition. Min. Typ. Max. Units. 1.7
该数据表的模型线
文件文字版本
link to page 5 link to page 5
ATtiny13A 1.6 Analog Comparator Characteristics Table 1-5.
Analog Comparator Characteristics, T = -40°C to +125°C A
Symbol Parameter Condition Min Typ Max Units
VAIO Input Offset Voltage VCC = 5V, VIN = VCC / 2 < 10 40 mV ILAC Input Leakage Current VCC = 5V, VIN = VCC / 2 -250 250 nA Analog Propagation Delay VCC = 2.7V 750 (from saturation to slight overdrive) VCC = 4.0V 500 tAPD ns Analog Propagation Delay VCC = 2.7V 100 (large step change) VCC = 4.0V 75 tDPD Digital Propagation Delay VCC = 1.8 - 5.5V 1 2 CLK Note: All parameters are based on simulation results.
1.7 Serial Programming Characteristics Table 1-6.
Serial Programming Characteristics, T = -40°C to +125°C A
Symbol Parameter Condition Min Typ Max Units
1/tCLCL Oscillator Frequency 0 1 MHz V = 1.8 – 5.5V CC tCLCL Oscillator Period 1000 ns 1/tCLCL Oscillator Frequency 0 9.6 MHz V = 2.7 – 5.5V CC tCLCL Oscillator Period 104 ns 1/tCLCL Oscillator Frequency 0 20 MHz VCC = 4.5 – 5.5V tCLCL Oscillator Period 50 ns t (1) SHSL SCK Pulse Width High 2 tCLCL ns t (1) SLSH SCK Pulse Width Low 2 tCLCL ns VCC = 1.8 – 5.5V tOVSH MOSI Setup to SCK High tCLCL ns tSHOX MOSI Hold after SCK High 2 tCLCL ns Note: 1. 2 t for f < 12 MHz, 3 t for f >= 12 MHz CLCL ck CLCL ck
5
8126F-Appendix B–AVR–05/12 Document Outline Appendix B – ATtiny13A Specification at 125°C 1. Electrical Characteristics 1.1 Absolute Maximum Ratings* 1.2 DC Characteristics 1.3 Clock Characteristics 1.3.1 Accuracy of Calibrated Internal Oscillator 1.4 System and Reset Characteristics 1.4.1 Enhanced Power-On Reset 1.5 ADC Characteristics 1.6 Analog Comparator Characteristics 1.7 Serial Programming Characteristics 2. Typical Characteristics 2.1 Current Consumption in Active Mode 2.2 Current Consumption in Idle Mode 2.3 Current Consumption in Power-down Mode 2.4 Current Consumption of Peripheral Units 2.5 Pull-up Resistors 2.6 Output Driver Strength (Low Power Pins) 2.7 Output Driver Strength (Regular Pins) 2.8 Input Thresholds and Hysteresis (for I/O Ports) 2.9 BOD, Bandgap and Reset 2.10 Internal Oscillator Speed 3. Ordering Information 4. Revision History
ATtiny13A 1.6 Analog Comparator Characteristics Table 1-5.
Analog Comparator Characteristics, T = -40°C to +125°C A
Symbol Parameter Condition Min Typ Max Units
VAIO Input Offset Voltage VCC = 5V, VIN = VCC / 2 < 10 40 mV ILAC Input Leakage Current VCC = 5V, VIN = VCC / 2 -250 250 nA Analog Propagation Delay VCC = 2.7V 750 (from saturation to slight overdrive) VCC = 4.0V 500 tAPD ns Analog Propagation Delay VCC = 2.7V 100 (large step change) VCC = 4.0V 75 tDPD Digital Propagation Delay VCC = 1.8 - 5.5V 1 2 CLK Note: All parameters are based on simulation results.
1.7 Serial Programming Characteristics Table 1-6.
Serial Programming Characteristics, T = -40°C to +125°C A
Symbol Parameter Condition Min Typ Max Units
1/tCLCL Oscillator Frequency 0 1 MHz V = 1.8 – 5.5V CC tCLCL Oscillator Period 1000 ns 1/tCLCL Oscillator Frequency 0 9.6 MHz V = 2.7 – 5.5V CC tCLCL Oscillator Period 104 ns 1/tCLCL Oscillator Frequency 0 20 MHz VCC = 4.5 – 5.5V tCLCL Oscillator Period 50 ns t (1) SHSL SCK Pulse Width High 2 tCLCL ns t (1) SLSH SCK Pulse Width Low 2 tCLCL ns VCC = 1.8 – 5.5V tOVSH MOSI Setup to SCK High tCLCL ns tSHOX MOSI Hold after SCK High 2 tCLCL ns Note: 1. 2 t for f < 12 MHz, 3 t for f >= 12 MHz CLCL ck CLCL ck
5
8126F-Appendix B–AVR–05/12 Document Outline Appendix B – ATtiny13A Specification at 125°C 1. Electrical Characteristics 1.1 Absolute Maximum Ratings* 1.2 DC Characteristics 1.3 Clock Characteristics 1.3.1 Accuracy of Calibrated Internal Oscillator 1.4 System and Reset Characteristics 1.4.1 Enhanced Power-On Reset 1.5 ADC Characteristics 1.6 Analog Comparator Characteristics 1.7 Serial Programming Characteristics 2. Typical Characteristics 2.1 Current Consumption in Active Mode 2.2 Current Consumption in Idle Mode 2.3 Current Consumption in Power-down Mode 2.4 Current Consumption of Peripheral Units 2.5 Pull-up Resistors 2.6 Output Driver Strength (Low Power Pins) 2.7 Output Driver Strength (Regular Pins) 2.8 Input Thresholds and Hysteresis (for I/O Ports) 2.9 BOD, Bandgap and Reset 2.10 Internal Oscillator Speed 3. Ordering Information 4. Revision History