Datasheet LTC3417A-2 (Analog Devices) - 3

制造商Analog Devices
描述Dual Synchronous 1.5A/1A 4MHz Step-Down DC/DC Regulator
页数 / 页20 / 3 — The. ELECTRICAL CHARACTERISTICS. denotes the specifi cations which apply …
文件格式/大小PDF / 345 Kb
文件语言英语

The. ELECTRICAL CHARACTERISTICS. denotes the specifi cations which apply over the full operating

The ELECTRICAL CHARACTERISTICS denotes the specifi cations which apply over the full operating

该数据表的模型线

文件文字版本

LTC3417A-2
The ELECTRICAL CHARACTERISTICS
l
denotes the specifi cations which apply over the full operating temperature range, otherwise specifi cations are at TA = 25°C. VIN = 3.6V unless otherwise specifi ed (Note 2). SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
VIN1, VIN2 Operating Voltage Range VIN1 = VIN2 2.25 5.5 V IFB1, IFB2 Feedback Pin Input Current VIN = 6V Pin Under Test = 3V ± 0.1 μA VFB1, VFB2 Feedback Voltage (Note 3) l 0.784 0.8 0.816 V ΔVLINEREG Reference Voltage Line Regulation. %/V VIN = 2.25V to 5V (Note 3) 0.02 0.2 %/V is the Percentage Change in VOUT with a Change in VIN ΔVLOADREG Output Voltage Load Regulation ITH1, ITH2 = 0.36V (Note 3) 0.02 0.2 % ITH1, ITH2 = 0.84V (Note 3) –0.02 –0.2 % gm(EA) Error Amplifi er Transconductance ITH1, ITH2(PINLOAD) = ±5μA (Note 3) 1400 μS IS Input DC Supply Current (Note 4) Active Mode VFB1 = VFB2 = 0.75V, VSYNC/MODE = VIN, 400 600 μA VRUN1 = VRUN2 = VIN IS Half Active Mode (VRUN2 = 0V, 1.5A Only) VFB1 = 0.75V, VSYNC/MODE = VIN, VRUN1 = VIN 260 400 μA Half Active Mode (VRUN1 = 0V, 1A Only) VFB2 = 0.75V, VSYNC/MODE = VIN, VRUN2 = VIN 260 400 μA Both Channels in Sleep Mode VFB1 = VFB2 = 1V, VSYNC/MODE = VIN, VRUN1 = 125 250 μA VRUN2 = VIN Shutdown VRUN1 = VRUN2 = 0V 0.01 1 μA fOSC Oscillator Frequency VFREQ = VIN 1.2 1.5 1.8 MHz VFREQ: RT = 143k 0.85 1 1.25 MHz VFREQ: Resistor (Note 6) 4 MHz ILIM1 Peak Switch Current Limit on SW1 (1.5A) 2.1 2.5 A ILIM2 Peak Switch Current Limit on SW2 (1A) 1.4 1.7 A RDS(ON)1 SW1 Top Switch On-Resistance (1.5A) VIN1 = 3.6V (Note 5) 0.088 Ω SW1 Bottom Switch On-Resistance VIN1 = 3.6V (Note 5) 0.084 Ω RDS(ON)2 SW2 Top Switch On-Resistance (1A) VIN2 = 3.6V (Note 5) 0.16 Ω SW2 Bottom Switch On-Resistance VIN2 = 3.6V (Note 5) 0.15 Ω ISW1(LKG) Switch Leakage Current SW1 (1.5A) VIN1 = 6V, VITH1 = 0V, VRUN1 = 0V 0.01 1 μA ISW2(LKG) Switch Leakage Current SW2 (1A) VIN2 = 6V, VITH2 = 0V, VRUN2 = 0V 0.01 1 μA VUVLO Undervoltage Lockout Threshold VIN1, VIN2 Ramping Down 1.9 2.07 2.2 V VIN1, VIN2 Ramping Up 1.95 2.12 2.25 V TPGOOD Threshold for Power Good. Percentage VFB1 or VFB2 Ramping Up –6 % Deviation from VFB Steady State VFB1 or VFB2 Ramping Down –6 % (Typically 0.8V) RPGOOD Power Good Pull-Down On-Resistance 120 300 Ω VRUN1, VRUN2 RUN1, RUN2 Threshold 0.3 0.85 1.5 V VPHASE PHASE Threshold High-CMOS Levels VIN –0.5 V PHASE Threshold Low-CMOS Levels 0.5 V IRUN1, IRUN2, IPHASE, RUN1, RUN2, PHASE and SYNC/MODE VIN = 6V, Pin Under Test = 3V ±0.01 ±1 μA ISYNC/MODE Leakage Current VTLSYNC/MODE SYNC/MODE Threshold Voltage Low 0.5 V VTHSYNC/MODE SYNC/MODE Threshold Voltage High VIN –0.5 V VTHFREQ FREQ Threshold Voltage High VIN –0.5 V 3417a2fa 3