Datasheet HVLED007 (STMicroelectronics) - 2

link to page 3 link to page 4 link to page 6 link to page 9 link to page 9 link to page 9 link to page 13 link to page 16 link to page 17 link to page 19 link to page 19 link to page 22 link to page 23 link to page 24 link to page 25 link to page 26 link to page 29 link to page 30 link to page 32
Contents HVLED007 Contents 1 Block diagram . 3 2 Pin connections . 4 3 Electrical characteristics . 6 4 Application information . 9
4.1 Introduction . 9 4.2 Input current shaping function - operating principle . 9 4.3 Operation of a Hi-PF QR flyback converter based on the HVLED007 . 13 4.4 Shaping capacitor (Ct) selection (pin CT) . 16 4.5 Control input for isolated feedback and optocoupler driving (pin COMP) 17 4.6 Multiplier input for input voltage sensing (pin MULT) . 19 4.7 Current sensing input (pin CS). Sense resistor (Rs) selection . 19 4.8 Zero current detection and triggering block (pin ZCD); starter . 22 4.9 Overload and short-circuit protection (OCP function) . 23 4.10 Overvoltage protection (OVP function) . 24 4.11 Soft-restart function . 25 4.12 Suggested step-by-step design procedure of a Hi-PF QR flyback converter based on the HVLED0007 26
5 Referenced documents . 29 6 Package information . 30 7 Revision history . 32
2/33 DS12866 Rev 1 Document Outline Table 1. Device summary 1 Block diagram Figure 1. Block diagram Table 2. Absolute maximum ratings 2 Pin connections Figure 2. Pin connection (top view) Table 3. Thermal data Table 4. Pin functions (continued) 3 Electrical characteristics Table 5. Electrical characteristics (continued) 4 Application information 4.1 Introduction Figure 3. Input current distortion in Hi-PF QR flyback converters with traditional TM control: current shape and resulting total harmonic distortion and power factor vs. Kv (= Vinpk/VR) ratio 4.2 Input current shaping function - operating principle Figure 4. Hi-PF QR flyback converter with the traditional TM control: current waveforms Figure 5. Input current shaper (ICS) block and its interconnection with HVLED007 control Figure 6. Key waveforms of the ICS circuit in figure 5 Figure 7. Shape of the current reference Vcsref(θ) (5) at different input voltages (i.e. Kv values) 4.3 Operation of a Hi-PF QR flyback converter based on the HVLED007 Table 6. Timing quantities in a HVLED007-based Hi-PF QR flyback converter Table 7. Control quantities in a HVLED007-based Hi-PF QR flyback converter Table 8. Electrical quantities in a HVLED007-based Hi-PF QR flyback converter 4.4 Shaping capacitor (Ct) selection (pin CT) 4.5 Control input for isolated feedback and optocoupler driving (pin COMP) Figure 8. Output characteristic of pin COMP and significant levels 4.6 Multiplier input for input voltage sensing (pin MULT) 4.7 Current sensing input (pin CS). Sense resistor (Rs) selection Figure 9. Effect of ripple on Ct on current sense signal: a) within linear dynamics, close to clamp level; b) signal slightly exceeding clamp level; c) signal exceeding clamp level, with OCP activation 4.8 Zero current detection and triggering block (pin ZCD); starter 4.9 Overload and short-circuit protection (OCP function) Figure 10. Functional schematic of the overload and short-circuit protection function 4.10 Overvoltage protection (OVP function) Figure 11. Functional schematic of the OVP function 4.11 Soft-restart function Figure 12. Functional schematic of the soft restart function 4.12 Suggested step-by-step design procedure of a Hi-PF QR flyback converter based on the HVLED0007 Table 9. Basic electrical specification and key parameters of a Hi-PF QR flyback Figure 13. Typical application schematic (reference for suggested design procedure) 5 Referenced documents 6 Package information Table 10. SO-8 mechanical data Figure 14. Package dimensions 7 Revision history Table 11. Document history